Why grout gets dirty (and stays that way)
Standard cement grout is essentially colored sand and cement, full of tiny pits and pores that drink up anything wet — mop water carrying dissolved dirt, shower water carrying soap and body oils, kitchen splashes carrying grease. As the water evaporates, the dirt stays behind inside the grout. That's why grout darkens gradually and why surface wiping never fixes it: the stain is in the grout, not just on it.
Two facts follow. First, dwell time matters more than scrubbing force — a cleaner needs minutes in contact with grout to loosen what's soaked in. Second, unsealed grout re-stains quickly, which is why this guide ends where our sealing guide begins. For shower mold, see the shower guide; for floors, the floor grout guide. Everything below suits cement grout between ceramic or porcelain tile; for epoxy grout or stone, check each method's cautions — or use the home-page finder.
What you'll need
- A stiff nylon grout brush (or an old firm toothbrush for small areas)
- Baking soda; hydrogen peroxide, standard 3% drugstore strength
- Powdered oxygen bleach (sodium percarbonate — the "oxy" laundry booster type)
- Dish soap, a spray bottle, a bucket, microfiber cloths or old towels, rubber gloves
- Optional: a steam cleaner with a small nylon brush nozzle
Before any method: remove loose dirt first, ventilate the room, wear gloves, and test your cleaner on one inconspicuous line for 10 minutes. Older grout and grout colorants can react unpredictably.
Method 1: Baking soda paste — the everyday default
Best for: general grime, light stains, routine deep cleans
Recipe: 3/4 cup baking soda + about 1/4 cup water, stirred to a thick paste (toothpaste consistency)
- Spread the paste along the grout lines with a gloved finger or old spatula, covering each line completely.
- Let it dwell 10–15 minutes. Mist lightly with water if it starts to dry out.
- Scrub along each line with the grout brush in short strokes; the paste's mild abrasion lifts dirt as you go.
- Wipe up the dirty paste with a damp cloth, rinsing the cloth often, then wipe once more with plain clean water.
- Buff dry with a towel — leftover moisture wicks remaining dirt back into the line.
Baking soda is the right first move for most jobs: gentle enough for monthly use and safe around glazed tile and stone. If lines still look shadowed afterward, move to Method 2 rather than scrubbing harder — chemistry does the lifting.
Method 2: Hydrogen peroxide — for stains and dingy white grout
Best for: set-in stains, yellowing, dingy light-colored grout, mild mold spots
Recipe: 1/2 cup baking soda + 1/4 cup hydrogen peroxide (3%) + 1 teaspoon dish soap
- Mix in a small bowl (it will fizz lightly) and apply along the lines with a brush or gloved finger.
- Dwell 10–15 minutes — peroxide needs contact time to break down stain pigments.
- Scrub, rinse thoroughly, and towel dry. For one stubborn spot, press a peroxide-soaked cotton ball onto it for 15 minutes first.
Peroxide is a mild oxidizer: it breaks apart the colored compounds in stains instead of just abrading the surface, reviving white grout that soda alone leaves gray. Two cautions: it can lighten colored grout with repeated use, so test first; and never mix it with vinegar — together they form peracetic acid, a harsh irritant.
Method 3: Oxygen bleach soak — for whole floors and big areas
Best for: large tiled areas, overall dinginess, grout that hasn't been cleaned in years
Recipe: 1/2 cup powdered oxygen bleach dissolved in 1 gallon of warm water (follow your product's label if it differs)
- Mop the solution generously over the tile so the grout lines are flooded, working in sections of about 25 square feet.
- Soak 20–30 minutes, re-wetting lines that start to dry. This long dwell is the entire point of the method.
- Scrub each line with the grout brush — after a proper soak, dirt releases with light pressure.
- Mop up with clean water, changing it when it looks dirty, and dry the floor with a towel.
Oxygen bleach (sodium percarbonate) releases hydrogen peroxide when dissolved, in a bucket-stable, color-safe form — the efficient way to treat a whole floor. Unlike chlorine bleach it's gentle on grout and makes no harsh fumes, but the powder is an eye and skin irritant: mix with gloves on, and check the label before using it around stone.
Method 4: Steam cleaning — the chemical-free deep clean
Best for: chemical-sensitive households, epoxy grout, heavy buildup, sanitizing
- Fill the steamer with plain water and fit the small nylon brush nozzle.
- Hold the nozzle an inch or two over a grout line and move slowly — about 1 inch per second — letting heat loosen the soil.
- Follow immediately with a microfiber cloth to wipe up the loosened, dirty water before it resettles.
- Work line by line. Expect a bathroom floor to take 20–40 minutes done properly.
Steam at the nozzle reaches around 212 °F or higher, melting grease, loosening dirt, and killing mold on contact — with nothing but water. It's the best option for epoxy grout, which pastes can dull. Keep the brush nylon, and go gently on cracked grout: if steam blasts out loose material, that grout needs repair, not cleaning.
What NOT to do
⚠ Never mix bleach with vinegar — or with ammonia
Chlorine bleach combined with any acid — vinegar, toilet bowl cleaner — releases chlorine gas; combined with ammonia it releases chloramine gas. Both can seriously damage lungs at household concentrations. Use one product at a time and rinse it completely away before using anything else. This single rule prevents nearly all home grout-cleaning injuries.
- No wire brushes, ever. Steel bristles gouge cement grout — leaving it rougher and faster to re-stain — and scratch glazed tile and stone. A stiff nylon brush is the strongest tool grout needs.
- Keep vinegar off natural stone. Vinegar (and lemon, and most limescale sprays) etches marble, travertine, limestone, and slate, dulling and pitting the surface, sometimes in one use. Stone gets a pH-neutral cleaner, always. On cement grout between ceramic tile, occasional diluted vinegar is tolerable, but frequent use slowly dissolves the grout itself — the methods above make it unnecessary.
- Don't soak grout with chlorine bleach as a routine. Used often, bleach degrades cement grout and can yellow grout colors. Reserve diluted bleach for serious mold (see the shower guide); prefer peroxide methods for stains.
- Don't flood and walk away. Standing dirty water re-deposits dirt into the lines as it dries. Always finish with a clean rinse and towel dry.
- Test colored or powdered cleansers first — some leave pigment in white grout's pores that reads as a new stain.
When cleaning isn't enough
If a line survives two proper deep cleans, the stain has likely soaked the full depth of unsealed grout. Three options remain. A grout colorant/refresh product (an epoxy-based coating that recolors and seals in one step) can make stained grout look new for years. Targeted regrouting — raking out the top 1/8 inch of the worst lines and packing in fresh grout — fixes stained or cracked sections. And if grout is crumbling everywhere, full regrouting is the honest fix.
Either way, cleaned grout should be sealed once fully dry — typically 24 hours after a deep clean. Sealing turns this from a quarterly chore into a quick wipe-down: see How to Seal Grout for types, application, and drying times.
Next guide How to Clean Shower Grout & Remove Mold → Black spots, pink film, and the habits that keep them from coming back.